Fast setting supa glue in a convenient bottle that allows easy, controlled and precise application. Features Easy, controlled application Non-drip glue saver nozzle, reduces waste and mess. Long fine nozzle for precise application Bonds a variety of surfaces Extremely fast setting Dries Clear for clean, neat results Water resistant No clamping necessary No mixing required Maximum strength achieved in 12 hours Only takes 45 seconds to achieve initial bond Non-clog cap Forms a rigid bond Upright self-standing bottle Comfortable to hold Where can this product be used? Ideal for small repair jobs or when immediate results are required. Water resistant not water proof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene. Leather may become hardened or discoloured For interior use only Not suitable for repairing items that are in direct contact with hot liquids Will not permanently bond glass or materials containing alkaline elements. Has no gap filling properties therefore surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Bonds a variety of porous and non-porous surfaces Metals China Rubber Leather Some plastics Wood How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Hold bottle in an upright position. Pierce seal by attaching nozzle and cap and turning clockwise. Remove cap and squeeze gently to apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. (30 seconds). The product grabs within 5-30 seconds, depending on environmental conditions and substrates to be bonded. Allow 30 minutes for sufficient bond strength for practical use. Maximum bond strength reached after 12 hours. Handy tips Cyanoacrylate adhesives can create a white residue on the surface of a substrate if the area is not well ventilated. Clean the affected area with acetone to remove residue. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. Excellent when used with other adhesives, as the temporary tack For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. Acetone (nail polish remover) or Olive oil can also be used to remove Quick Fix from skin. While superglue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Super glues cure more slowly when large amounts are used. For faster cure use sparingly. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Reseal cap in a clockwise direction. Tap bottle lightly on a flat surface to clear excess product from nozzle. To remove excess from substrates, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using thias method. Ensure cap is replaced and store in a cool dry place. Cyanoacrylate based adhesives polymerise in the presence of moisture. Store Upright. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
